Iopener
Author: m | 2025-04-24
Place an iOpener into the hot water for 2-3 minutes. Make sure the iOpener is fully submerged in the water. Use tongs to extract the heated iOpener from the hot water. Thoroughly dry the iOpener with a towel. The iOpener will be very hot, so be careful to hold it only by the end tabs. Your iOpener is ready for use! IOpener -melanoma NL-CA IOpener -NSCLC NL-CA IOpener - General Information 2025 PamGene International B.V.
iOpener: Beatrix Potter (iOpeners) Kindle Edition
Work for you. Skip the next two steps. Apply a heated iOpener to the screen to loosen the adhesive underneath. Apply the iOpener for at least 3 minutes. A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the device. The edge should feel slightly too hot to the touch. Once the screen is warm to the touch, apply a suction handle to the bottom edge of the screen. If your display is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the broken screen. Lift the screen including its safety frame with the suction handle to create a small gap between the screen and the phone assembly. Depending on the age of your phone, this may be difficult. If you're having trouble, apply more heat to the bottom edge and try again. Insert an opening pick into the gap. To avoid damaging your phone, don't insert your pick more than ~2.5 mm as you separate the screen adhesive. Note the following areas: The screen cable is a little less than halfway up the left edge of the phone. Be very careful here to avoid tearing the cable. There are many spring contacts around the perimeter of the phone. Be very careful in these areas to avoid bending the contacts. Slide the opening pick to the bottom right corner of the screen to slice its adhesive. Leave the opening pick in place to prevent the adhesive from resealing. Insert a second opening pick at the bottom edge and slide it to the bottom left corner of the screen to slice the adhesive. Leave the opening pick in place to prevent the adhesive from resealing. Insert a third opening pick underneath the bottom left corner of the screen. Slide the opening pick along the left edge of the screen to slice the adhesive and to release the plastic clips. Leave the opening pick in the top left corner to prevent the adhesive from resealing. If the adhesive becomes hard to cut, it has most likely cooled down. Use your iOpener or heat gun for 1-2 minutes to reheat it. When you slice near the front facing camera, insert only the tip of the opening pick (~2.5 mm) to avoid damaging or smearing the camera. Insert a fourth opening pick at the top left corner of the screen. Slide the opening pick along the top edge of the phone to slice the adhesive. Leave the opening pick in the top right corner
The iOpener Happiness at Work Assessment - iOpener Institute
Allow your battery to drain below 25% before starting this repair. A charged battery may catch fire if damaged. Fully power off your phone and unplug any cables. The screen of the Google Pixel 7 is held in place by a safety frame of plastic clips and adhesive. During the removal procedure, make sure to insert your opening picks under the safety frame to avoid separating it from the screen. Only insert the pick up to ~3.5 mm during the removal procedure to avoid damaging the internals and to avoid interfering with the plastic clips. There are several plastic clips around the whole screen. In case your opening pick gets blocked during the screen removal procedure it means you inserted your pick too deep underneath the screen. Tool used on this step: Clampy - Anti-Clamp$24.95 The next three steps demonstrate the Anti-Clamp, a tool we designed to make the opening procedure easier. If you aren't using the Anti-Clamp, skip down three steps for an alternate method. For complete instructions on how to use the Anti-Clamp, check out this guide. If your screen is cracked, cover it with a layer of clear packing tape to help the suction cup adhere. Pull the blue handle backwards to unlock the Anti-Clamp's arms. Slide the arms over either the left or right edge of your phone. Position the suction cups near the bottom edge of the phone—one on the front, and one on the back. Squeeze the cups together to apply suction. If you find that the surface of your phone is too slippery for the Anti-Clamp to hold onto, you can use tape to create a grippier surface. Pull the blue handle forward to lock the arms. Turn the handle clockwise 360 degrees or until the cups start to stretch. Make sure the suction cups remain aligned with each other. If they begin to slip out of alignment, loosen the suction cups slightly and realign the arms. Heat an iOpener and thread it through the arms of the Anti-Clamp. You can also use a hair dryer or heat gun—but extreme heat can damage the display and/or internal battery, so proceed with care. Fold the iOpener so it lays on the bottom edge of the phone. Wait one minute to give the adhesive a chance to release and present an opening gap. Insert an opening pick under the screen frame when the Anti-Clamp creates a large enough gap. If the Anti-Clamp doesn't create a sufficient gap, apply more heat to the area and rotate the handle clockwise half a turn. Don't crank more than a half a turn at a time, and wait one minute between turns. Let the Anti-Clamp and time do theiOpener: Going to School (iOpeners) Kindle Edition - amazon.com
. Place an iOpener into the hot water for 2-3 minutes. Make sure the iOpener is fully submerged in the water. Use tongs to extract the heated iOpener from the hot water. Thoroughly dry the iOpener with a towel. The iOpener will be very hot, so be careful to hold it only by the end tabs. Your iOpener is ready for use!iOpener: Skeletons Inside and Out (iOpeners) Kindle Edition
No, but it does make things easier when dealing with Tough adhesive in electronics and displays.You will need to heat the glue somehow, if you have a heat gun laying around you could use that at a low temperature to make the glue soft.If you do not heat the glue for example on a LCD that has Display glued Glass Panel you risk breaking the Glass/Or the screen which would come into more expensive repairs. If you only need to Replace the Glass it would be better to heat the glue to remove it.In all although you don't necessarily need it, it makes the job much easier and faster to avoid damage.Another thing to note is, The iOpener is more precise in where you need heat, Where as a Heat gun blows air on components that could become damaged. In Example: Circuitry.I myself would recommend it for the safety of the Device. Was this answer helpful? Score 13 CancelScroll through this thread to find the appropriate place for this comment. Then, click "Attach comment to this post" to move it.iFixit's iOpener Kit! - YouTube
Tweezers$4.99 Use a pair of tweezers to carefully peel the lower graphite foil off the battery and midframe. If you're having a hard time peeling off the foil, apply a heated iOpener to the foil for two minutes to loosen its adhesive. Use a Torx T3 screwdriver to remove the three 5.1 mm-long screws securing the loudspeaker. Use a pair of tweezers to lift the loudspeaker out of its recess and remove it. Use a Torx T3 screwdriver to remove the nine 5.1 mm-long screws securing the midframe. Tool used on this step: Tweezers$4.99 Use a pair of tweezers to remove the midframe. During reassembly check the condition of the thermal pad. If it's damaged, remove the pad, clean the area with high-concentration (greater than 90%) isopropyl alcohol and a microfiber or lint-free cloth, and apply a new thermal pad. Use a spudger to disconnect the battery cable by prying the connector straight up from its socket. The next six steps show how to remove the mmWave antenna. Use a Torx T3 screwdriver to remove the 5.1 mm-long screw securing the mmWave antenna bracket. Insert a spudger underneath the bottom right edge of the mmWave antenna bracket. Pry upwards to loosen the mmWave antenna bracket. Tool used on this step: Tweezers$4.99 Use a pair of tweezers to remove the mmWave antenna bracket. Use a spudger to disconnect the mmWave antenna cable by prying the connector straight up from its socket. Use a pair of tweezers to lift the mmWave antenna (including its cable) out of its recess. Remove the mmWave antenna assembly. During reassembly check the condition of the thermal pad. If it's damaged, remove the pad, clean the area with high-concentration (greater than 90%) isopropyl alcohol and a microfiber or lint-free cloth, and apply a new thermal pad. Use a Torx T3 screwdriver to remove the 5.1 mm-long screw securing the rear cameras. Use a spudger to disconnect the wide-angle camera cable by prying the connector straight up from its socket. Tool used on this step: Tweezers$4.99 Use a pair of tweezers to remove the wide-angle camera. Use a spudger to disconnect the ultra wide-angle camera cable by prying the connector straight up from its socket. Use a pair of tweezers to remove the ultra wide-angle camera.SOLVED: Is There an alternative to the iOpener - iFixit
. Place an iOpener into the hot water for 2-3 minutes. Make sure the iOpener is fully submerged in the water. Use tongs to extract the heated iOpener from the hot water. Thoroughly dry the iOpener with a towel. The iOpener will be very hot, so be careful to hold it only by the end tabs. Your iOpener is ready for use! IOpener -melanoma NL-CA IOpener -NSCLC NL-CA IOpener - General Information 2025 PamGene International B.V.Comments
Work for you. Skip the next two steps. Apply a heated iOpener to the screen to loosen the adhesive underneath. Apply the iOpener for at least 3 minutes. A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the device. The edge should feel slightly too hot to the touch. Once the screen is warm to the touch, apply a suction handle to the bottom edge of the screen. If your display is badly cracked, covering it with a layer of clear packing tape may allow the suction cup to adhere. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the broken screen. Lift the screen including its safety frame with the suction handle to create a small gap between the screen and the phone assembly. Depending on the age of your phone, this may be difficult. If you're having trouble, apply more heat to the bottom edge and try again. Insert an opening pick into the gap. To avoid damaging your phone, don't insert your pick more than ~2.5 mm as you separate the screen adhesive. Note the following areas: The screen cable is a little less than halfway up the left edge of the phone. Be very careful here to avoid tearing the cable. There are many spring contacts around the perimeter of the phone. Be very careful in these areas to avoid bending the contacts. Slide the opening pick to the bottom right corner of the screen to slice its adhesive. Leave the opening pick in place to prevent the adhesive from resealing. Insert a second opening pick at the bottom edge and slide it to the bottom left corner of the screen to slice the adhesive. Leave the opening pick in place to prevent the adhesive from resealing. Insert a third opening pick underneath the bottom left corner of the screen. Slide the opening pick along the left edge of the screen to slice the adhesive and to release the plastic clips. Leave the opening pick in the top left corner to prevent the adhesive from resealing. If the adhesive becomes hard to cut, it has most likely cooled down. Use your iOpener or heat gun for 1-2 minutes to reheat it. When you slice near the front facing camera, insert only the tip of the opening pick (~2.5 mm) to avoid damaging or smearing the camera. Insert a fourth opening pick at the top left corner of the screen. Slide the opening pick along the top edge of the phone to slice the adhesive. Leave the opening pick in the top right corner
2025-04-06Allow your battery to drain below 25% before starting this repair. A charged battery may catch fire if damaged. Fully power off your phone and unplug any cables. The screen of the Google Pixel 7 is held in place by a safety frame of plastic clips and adhesive. During the removal procedure, make sure to insert your opening picks under the safety frame to avoid separating it from the screen. Only insert the pick up to ~3.5 mm during the removal procedure to avoid damaging the internals and to avoid interfering with the plastic clips. There are several plastic clips around the whole screen. In case your opening pick gets blocked during the screen removal procedure it means you inserted your pick too deep underneath the screen. Tool used on this step: Clampy - Anti-Clamp$24.95 The next three steps demonstrate the Anti-Clamp, a tool we designed to make the opening procedure easier. If you aren't using the Anti-Clamp, skip down three steps for an alternate method. For complete instructions on how to use the Anti-Clamp, check out this guide. If your screen is cracked, cover it with a layer of clear packing tape to help the suction cup adhere. Pull the blue handle backwards to unlock the Anti-Clamp's arms. Slide the arms over either the left or right edge of your phone. Position the suction cups near the bottom edge of the phone—one on the front, and one on the back. Squeeze the cups together to apply suction. If you find that the surface of your phone is too slippery for the Anti-Clamp to hold onto, you can use tape to create a grippier surface. Pull the blue handle forward to lock the arms. Turn the handle clockwise 360 degrees or until the cups start to stretch. Make sure the suction cups remain aligned with each other. If they begin to slip out of alignment, loosen the suction cups slightly and realign the arms. Heat an iOpener and thread it through the arms of the Anti-Clamp. You can also use a hair dryer or heat gun—but extreme heat can damage the display and/or internal battery, so proceed with care. Fold the iOpener so it lays on the bottom edge of the phone. Wait one minute to give the adhesive a chance to release and present an opening gap. Insert an opening pick under the screen frame when the Anti-Clamp creates a large enough gap. If the Anti-Clamp doesn't create a sufficient gap, apply more heat to the area and rotate the handle clockwise half a turn. Don't crank more than a half a turn at a time, and wait one minute between turns. Let the Anti-Clamp and time do the
2025-04-03No, but it does make things easier when dealing with Tough adhesive in electronics and displays.You will need to heat the glue somehow, if you have a heat gun laying around you could use that at a low temperature to make the glue soft.If you do not heat the glue for example on a LCD that has Display glued Glass Panel you risk breaking the Glass/Or the screen which would come into more expensive repairs. If you only need to Replace the Glass it would be better to heat the glue to remove it.In all although you don't necessarily need it, it makes the job much easier and faster to avoid damage.Another thing to note is, The iOpener is more precise in where you need heat, Where as a Heat gun blows air on components that could become damaged. In Example: Circuitry.I myself would recommend it for the safety of the Device. Was this answer helpful? Score 13 CancelScroll through this thread to find the appropriate place for this comment. Then, click "Attach comment to this post" to move it.
2025-03-25Tweezers$4.99 Use a pair of tweezers to carefully peel the lower graphite foil off the battery and midframe. If you're having a hard time peeling off the foil, apply a heated iOpener to the foil for two minutes to loosen its adhesive. Use a Torx T3 screwdriver to remove the three 5.1 mm-long screws securing the loudspeaker. Use a pair of tweezers to lift the loudspeaker out of its recess and remove it. Use a Torx T3 screwdriver to remove the nine 5.1 mm-long screws securing the midframe. Tool used on this step: Tweezers$4.99 Use a pair of tweezers to remove the midframe. During reassembly check the condition of the thermal pad. If it's damaged, remove the pad, clean the area with high-concentration (greater than 90%) isopropyl alcohol and a microfiber or lint-free cloth, and apply a new thermal pad. Use a spudger to disconnect the battery cable by prying the connector straight up from its socket. The next six steps show how to remove the mmWave antenna. Use a Torx T3 screwdriver to remove the 5.1 mm-long screw securing the mmWave antenna bracket. Insert a spudger underneath the bottom right edge of the mmWave antenna bracket. Pry upwards to loosen the mmWave antenna bracket. Tool used on this step: Tweezers$4.99 Use a pair of tweezers to remove the mmWave antenna bracket. Use a spudger to disconnect the mmWave antenna cable by prying the connector straight up from its socket. Use a pair of tweezers to lift the mmWave antenna (including its cable) out of its recess. Remove the mmWave antenna assembly. During reassembly check the condition of the thermal pad. If it's damaged, remove the pad, clean the area with high-concentration (greater than 90%) isopropyl alcohol and a microfiber or lint-free cloth, and apply a new thermal pad. Use a Torx T3 screwdriver to remove the 5.1 mm-long screw securing the rear cameras. Use a spudger to disconnect the wide-angle camera cable by prying the connector straight up from its socket. Tool used on this step: Tweezers$4.99 Use a pair of tweezers to remove the wide-angle camera. Use a spudger to disconnect the ultra wide-angle camera cable by prying the connector straight up from its socket. Use a pair of tweezers to remove the ultra wide-angle camera.
2025-04-21